Make sure both sockets slide back and lock the lamp into position. DO NOT FRAY Lamp wire ends - watch the Roll Lock Installation Video for proper installation. Prior to plugging power into unit, install ILUMINAR DE lamp into the fixture, be sure to wear proper gloves when handling the lamp. This will improve lamp life and performance. Panels should only support a total amperage of 80% of its capacity (100 amp panel should never exceed 80 amps).įor proper lamp break-in, we recommend that you run the remote ballast and lamp at 100% power for at least 100 straight hours after initial startup. If you are using a light controller ONLY bring a ground wire and two hot leads from your electrical panels.Ĭheck electrical panel to ensure proper voltage is available for the number of fixture installed. The input for the ballast is 2 HOT WIRES and 1 GROUND WIRE. Request A Professional Light LayoutĪll digital ballasts may malfunction if the circuit has a neutral. When possible, have a licensed/certified/insured electrician install fixtures or aid in the electrical layout plans and/or diagrams prior to installation. These cords/connections are not designed to bear weight.ĭO NOT make contact with the interior of the socket while power is on.ĭO NOT plug the system into untested or unidentified voltage other than what is designated on ballast.ĭO NOT attempt to rewire, alter, modify or reconfigure your system - this will void the ILUMINAR warranty and could cause serious safety hazards, or cause bodily injury or death, as this is a high amperage and voltage device.ĭO NOT plug or unplug the lamp cord while the ballast is connected to power.ĭO NOT use this with a flip or switch box system, it will void the warranty. Make sure power cord and lamp cord are connected properly.ĭisconnect power before changing the lamp.ĭO NOT open the ballast case, it will void the warranty.ĭO NOT support the ballast by power cord(s) and/or lamp cord(s). Make sure lamp is correctly locked into the Roll Lock Socket, properly securing the lamp. Make sure to wear proper gloves to protect from the transfer of oil from the skin to the lamps glass surface. When changing out the lamp, make sure that the lamp has time to cool before touching. If the lamp is damaged in any way (cracks, loose internal connections), replace lamp immediately. In addition, failure to follow these safety warnings can/will result in a waiver of all liabilities and will void all warranties. Any damage to products not in their original packaging will not be covered under warranty.įailure to observe the following safety warnings and or instructions may result in serious injury. Always have an expert(s) install your fixtures when possible.Īll returns will need to be in the original ILUMINAR packaging in order to avoid product damage during shipping. The following is a general set of warnings and basic guidelines for your product. We strive to deliver the best product possible and will do our best to make sure you are satisfied. (For example, you can have the power relay plugged into your dehumidifier so you can also monitor and control the humidity in the grow room remotely). You can then set them to turn on or off or automatically trigger based on conditions you set in the application. The relays can be used to connect any piece of equipment you’re running and can operate 0-48V. It will display in realtime the temperature as well as historical data of the grow environment and it also has 2 hard-wired relays onboard (1 per zone). The HASH Controller alone will monitor and control lighting (turning lights on and off as well as dimming) remotely via the ILUMINAR Lighting Controller iPhone/Android App. What does the HASH Controller do without the addition of the HASH Environmental Sensor? If location services are turned off, you will not be able to connect to the HASH Controller. Why do I get an error when trying to connect my Hash Controller via wifi?Įnsure your location services are turned ON in the ILUMINAR Lighting Controller mobile application in order to properly install and connect to the HASH Controller for the first time. There are automatic rules embedded in the software to make sure your garden is safe. Your temperature probes must be connected to the HASH Controller for the application to operate. This occurs if your terminal hubs are not connected to your temperature probes. Why does my light turn on and off instantly? The HASH Controller works with everything that runs 0-10V, 1-10V, 5-10V What is the HASH Controller compatible with? Click the following links to view/purchase the correct cable. Ensure you have purchased the cable to connect the first fixture to the HASH before you begin installation.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |